Thinking about switching out a shaft or clubhead? Today I’m going to show how to use a golf shaft puller and demonstrate the one I recently purchased.
A quick primer: A golf shaft puller is a tool designed to remove the shaft from the clubhead without causing damage to either component. It works by applying pressure to the hosel, the part of the clubhead where the shaft is inserted and secured with epoxy. By breaking down the epoxy, the shaft can be safely removed and replaced with a new one.
Using a golf shaft puller can be a little tricky at first, but with the right technique and a bit of practice, it can be a simple and efficient process. Truth be told if you are removing just a single clubhead from a shaft, you might just want to be careful in heating the hosel and then remove the clubhead while wearing a glove. If you are going to change out multiple heads or shafts in your set, go ahead and get a shaft puller. It makes life much easier. In this article, we will guide you through the steps of how to use a golf shaft puller to remove the shaft from your clubhead, so you can upgrade your golf clubs with confidence.
So this is the shaft puller I purchased.
Golf Club Shaft Puller Extractor for Steel & Graphite SHAFTS
The product was basically put together with the exception of including a hosel protector and a rubber vise clamp. There were also some quick instructions in the box as well. The hosel protector accommodates standard shaft sizes of .335 to .370 diameters. This golf shaft puller works with both steel as well as graphite shafts.
My recommendation is to mount the shaft puller to a workbench. I built a temporary workbench where I’m trying to see what it takes to make a 1941 tube radio come back alive so I didn’t want to attach the shaft puller I purchased to the bench. But… do yourself a favor and stabilize your shaft puller with a couple of bolts.
Golf Club Shaft Puller Extractor for Steel & Graphite SHAFTS
If you want to change the shaft on your golf club, you’ll need a tool to remove it. A golf club shaft puller extractor is the perfect tool for the job. This tool will work on both steel and graphite shafts, and it’s a must-have for any avid golfer who wants to customize their clubs.
To use the golf club shaft puller extractor, you’ll need a heat source. A micro torch or heat gun is recommended. Heat the hosel for about 30 seconds to loosen the epoxy that holds the shaft in place. Then, place the golf club shaft puller extractor on the shaft and tighten the clamp. Turn the screw on the extractor until the shaft pops out of the clubhead.
It’s important to note that you should use caution when using the golf club shaft puller extractor. Make sure you follow the instructions carefully and wear protective gear, such as gloves and safety glasses. Also, be sure to use the right amount of heat, as too much heat can damage the clubhead.
Overall, the golf club shaft puller extractor is a great tool to have if you want to customize your golf clubs. It’s easy to use and can save you a lot of money in the long run by allowing you to change out shafts yourself instead of paying a professional to do it for you.
How to Use a Golf Shaft Puller
Step 1: Secure the Clubhead and Shaft
Before using a golf shaft puller, you need to secure the clubhead and shaft. Actually, prior to that you should remove the ferrule. You can either use a heat gun or butane torch to heat up the ferrule and then use needle nose pliers or a utility knife to remove the ferrule. After the ferrule has been removed, put the shaft in the rubber clamp and then situate the club so the hosel protector goes around the hosel of the club. Then, clamp the shaft in the puller. I had to tighten up a bolt with an adjustable wrench, which in turn tightens up the rubber clamp around the shaft.
Step 2: Apply Heat to the Hosel
Next, you need to apply heat to the hosel. I used a butane torch for probably a minute 45 seconds or so. If you choose to use a heat gun, you’ll probably be 3 minutes plus. This process will break down the epoxy that holds the clubhead to the shaft. Be careful not to overheat the hosel, as this can damage the clubhead and shaft. Please read that last sentence again. Make sure to go around the hosel and not place the heat for very long in the same place.
Step 3: Tighten the Puller
Now, you need to tighten the puller. This is done by taking the bar to pump up the hydraulic bottle jack. As you pump, this applies pressure between the shaft and hosel. This pressure will gradually pull the clubhead out of the shaft. I do have to say that the first time I used the butane torch, it did not loosen the epoxy enough. So when I pumped up the hydraulic bottle jack, it did not loosen the clubhead. Not a fault whatsoever with this device, it was purely operator error. I heated the hosel another 45 seconds and that did the trick.
Step 4: Remove the Clubhead From the Shaft
Once the puller has applied enough pressure, the clubhead should loosen from the shaft. Carefully remove the clubhead. Now loosen the bolt with an adjustable wrench to remove the shaft from the puller and take the rubber clamp off the shaft.
Step 5: Loosen the Quick Release – Tighten the Quick Release
Take the crimped part of the bar and loosen the quick release. Then push down on the top portion of the golf shaft puller. Then tighten the quick release. Now you are ready to work on your next club.
What Do I Think About the Golf Club Shaft Puller Extractor for Steel & Graphite SHAFTS?
I’m a happy camper. I realized that in using this product for the very first time, I attached the club to the shaft puller, tightened everything down, applied heat to the hosel, pumped up the hydraulic bottle jack and the clubhead was easily removed from the shaft, all within 5 minutes. I would have to say that I could easily knock a minute or so off that time the 2nd time around. I’m not so sure I even read the directions. Having said that, I would bolt down this product for efficiency and safety reasons.
Before I used this product I would hold the golf club by hand and heat up the hosel, while spinning the club and attempting to use a butane torch or heat gun. Then after a while I would attempt to remove the clubhead by hand. Yes this worked but not the most efficient way of doing things.
I’m not sure what else I can say except this is a sturdy unit that gets the job done. I couldn’t ask for anything more and now that I’ve put it to use, it will become a fantastic addition to my golf cave. I’m not so sure I want to tell my friends about this shaft puller for fear that they will put me to work.
Because I now own this golf club shaft puller, whenever I think of changing out a shaft or clubhead it will be put to use.
As I understand it, it is important to note that not all shaft pullers are created equal. Some are designed specifically for graphite shafts, while others are better suited for steel shafts. This shaft puller works with both steel and graphite shafts. Just please be careful in tightening the rubber clamp around the shaft. I’ve been told that wrapping tape around the shaft can be what you might call a safety feature.
The bottom line. Buy this product. By mastering the art of golf shaft pulling, you can save time and money by repairing and customizing your own clubs. Plus, you’ll have the satisfaction of knowing that you did it yourself. So, grab your shaft puller and get to work!